Introduction:
one. HS sequence slurry pump is developed for the continuous pumping of higher abrasive, EPT slurries with small maintenance demands. The wearing parts are produced of ultra chrome or and rubber. It will sustain higher effectiveness more than the use daily life of its factors.
2. The metal damp elements and rubber ones can be interchangeable for handling diverse liquids or slurries.
three. HS slurry pumps are obtainable in dimensions ranging from 1 inch to 18 inch discharge and feature high performance efficiency capable of flow rates from ten.eight to 5400 m sup3/h and heads up to 125 meters for large head versions.
Functions:
1. Cylindrical composition of bearing assembly: hassle-free to adjust the space among impeller and JCEP liner
and can beremoved entirely
two. Interchangeable anti-abrasive moist parts created of large-chrome alloys
three. Casing halves of ductile iron with exterior reinforcing ribs offer substantial operating stress capabilities
and an additional measure of security.
four. The discharge department can be oriEPTTd to any eigEPTT positions at the interval of 45 levels
five. Various EPT types: DC(immediate link), V-belt EPT, EPT box EPTT, EPT couplings, VFD,
SCR management, and so on
six. The shaft seal makes use of the EPTT seal, expeller seal and mechanical seal
Typical Software:
| #8226 EPT | #8226 Mineral processing | #8226 EPTT prep | #8226 Cyclone feeds |
| #8226 Tunnel | #8226 EPTT slurries | #8226 EPTEPTTngs | #8226 Mill grinding |
| #8226 Ash hXiHu (West EPT) Dis.Hu (West EPT) Dis. | #8226 Paper and Pulp | #8226 Waste sludge | #8226 Coarse sand |
| #8226 Lime mud | #8226 Phosphoric acid | #8226 EPTT | #8226 EPTT |
| #8226 Alumina JCEP | #8226 EPTT Plant | #8226 Potash FerEPTTzer Plant | #8226 Other EPTT |
| Design | Max EPTT (Kw) |
Inlet amp Outlet measurement (inch) | EPT for Put on Parts | Flow Charge (Q) | EPT (H) meter |
Pace (RPM) |
EPTTeller Dia. (mm) |
|
| m sup3/hr | l/s | |||||||
| 25HS-B | 15 | one.five/one | M | 12.6~28.8 | 3.five~8 | six~sixty eight | 1200~3800 | 152 |
| R | ten.8~twenty five.2 | three~7 | 7~fifty two | 1400~3400 | 152 | |||
| 40HS-B | fifteen | two/1.five | M | 32.four~seventy two | 9~20 | six~58 | 1200~3200 | 184 |
| R | 25.two~fifty four | 7~fifteen | five.five~forty one | 1000~2600 | 178 | |||
| 50HS-C | thirty | three/two | M | 39.6~86.four | 11~24 | 12~64 | 1300~2700 | 214 |
| R | 36~75.6 | 10~21 | 13~forty six | 1300~2300 | 213 | |||
| 75HS-C | 30 | four/three | M | 86.four~198 | 24~55 | 9~52 | a thousand~2200 | 245 |
| R | 79.2~180 | 22~50 | 5~34.five | 800~1800 | 245 | |||
| 100HS-D | 60 | six/four | M | 162~360 | forty~100 | 12~56 | 800~1550 | 365 |
| R | one hundred forty four~324 | 40~90 | twelve~45 | 800~1350 | 365 | |||
| 150HS-E | 120 | eight/six | M | 360~828 | one hundred~230 | 10~sixty one | five hundred~1140 | 510 |
| R | 324~720 | ninety~two hundred | 7~forty nine | 400~1000 | 510 | |||
| 200MS-E | a hundred and twenty | ten/eight | M | 666~1440 | 185~four hundred | fourteen~sixty | 600~1100 | 549 |
| 200HS-ST | 560 | ten/8 | M | 612~1368 | 170~380 | 11~sixty one | 400~850 | 686 |
| R | 540~1188 | a hundred and fifty~330 | twelve~50 | four hundred~750 | 686 | |||
| 250HS-ST | 560 | 12/10 | M | 936~1980 | 260~550 | seven~sixty eight | 300~800 | 762 |
| R | 720~1620 | 200~450 | seven~forty five | three hundred~650 | 762 | |||
| 300HS-TU | 560 | 14/12 | M | 1260~2772 | 350~770 | 13~sixty three | three hundred~600 | 965 |
| R | 1152~2520 | 320~seven-hundred | thirteen~forty four | 300~500 | 965 | |||
| 350HS-TU | 1200 | sixteen/14 | M | 1368~3060 | 380~850 | eleven~63 | 250~550 | 1067 |
| 450HS-TU | 1200 | twenty/eighteen | M | 2520~5400 | 700~1500 | thirteen~fifty seven | 200~four hundred | 1370 |
| 25HHS-C | 30 | 1.5/1 | M | sixteen.two~34.2 | four.five~9.five | twenty five~ninety two | 1400~2200 | 330 |
| 50HHS-D | 60 | three/two | M | 68.4~136.eight | 19~38 | 25~87 | 850~1400 | 457 |
| 75HHS-E | a hundred and twenty | four/three | M | 126~252 | 35~70 | twelve~97 | 600~1400 | 508 |
| 100HHS-E | 120 | 6/4 | M | 324~720 | 90~two hundred | 30~118 | 600~1000 | 711 |
| 150HHS-S | 560 | eight/6 | M | 468-1008 | 130~280 | 20~ninety four | 500~one thousand | 711 |
For the material of putting on areas,
quotM quot = metal, ultra chromium alloy quotR quot = anti-abrasive rubber
Speak to
Welcome to make contact with us any time for particulars.
Your inquiry will get our prompt attention and response !
